York Pattern Victorian Tiled Hallway Restored in Wanstead, E11

Victorian black and white tiles in the hallway of a house in Wanstead (E11), laid in what is often referred to as the York Pattern with a Kingsley Border, however sadly neglected for many years after being covered with a heavy underlay and carpet.

York Patten Victorian Floor Tiles Before Cleaning Wanstead

Restoring a Victorian Floor

First we cleaned the tiles with a dilution of Tile Doctor Pro-clean which releases the dirt stuck in the pores of the tiles; the solution was scrubbed into the floor with a buffer machine fitted with a black scrubbing pad and then the released soil extracted with a wet vacuum. The floor was then rinsed with water and extracted again with the wet vacuum. It was left to dry for thirty minutes and the floor inspected which revealed a few stubborn areas that were then treated using Nano-Tech Heavy Build-up remover (HBU) which was left to dwell for forty minutes and then scrubbed and then extracted again with water.

York Patten Victorian Floor Tiles Before and After Cleaning Wanstead

To Slow down or stop the possibility of an issue we sometimes have with older floors such as Victorian Tiles we often use a product developed by Tile Doctor called Acid Gel, this is left on the surface for 5 minutes and then removed with light agitation and water and a wet vac machine, the floor is then rinsed with water again just to make sure there is no Acid Gel left in the Tile or on the surface. The Acid Gel not only Keeps mineral salts (efflorescence) at bay but also helps as a bonding agent for the sealer to make sealing theses type of tiles a lot easier.

Sealing a Victorian Tiled Hallway

After leaving the floor to dry overnight I came back the next day to seal the floor using four coats of Tile Doctor Seal and Go which is ideal for Victorian tiled floors as it leaves a low sheen finish whilst providing excellent stain protection.

York Patten Victorian Floor Tiles After Cleaning Wanstead

 
 

Victorian Tiled floor Restoration in London

Refurbishing a Marble Onyx Countertop in Hampstead

My client asked me to take a look at a very dirty Marble Onyx countertop in her home in Hampstead which is located within the London Borough of Camden. Interestingly, Hampstead is home to more millionaires than any other area of the UK so if you’re going to find bathrooms of this standard this is the place.

Marble Onyx Countertop London Before and After Cleaning

This particular worktop had been heavily soiled by roughly fifteen years of soap scum and old sealer. It would take a thorough clean as well as a fresh seal to get this countertop back to looking its best. Marble is a fantastic type of stone which has, throughout history, been used to forge beautiful, yet resilient surfaces.

Cleaning a dirty Marble Onyx countertop

I immediately set to work cleaning the countertop using a strong solution of Tile Doctor Pro-Clean. Pro-Clean is an alkaline product and therefore suitable for use on natural stone, meaning that, along with Marble, it is also suitable for use on Limestone, Granite, Slate, Travertine, and others. After leaving it to dwell on the surface for a short period of time, I began scrubbing the solution of cleaner into the Marble, and gradually the years of soap scum, old sealer and ingrained dirt began to come off. It was amazing just how quickly I was able to remove many years of muck with a bit of elbow grease.

Following this, I rinsed off any excess cleaning product with clean water and then left the surface to dry, before I began the process of burnishing the Marble countertop using small six inch burnishing pads starting with a coarse pad and then moving up to super fine. After the burnishing process was complete, I gave the surface a rinse followed by an additional polish with a buffing pad until the shine was fully restored to the worktop.

Marble Onyx Countertop London Before and After Cleaning

Sealing a Marble Onyx countertop

After ensuring the countertop was fully dry following the cleaning and burnishing processes, I set about providing the surface with a fresh seal. My choice of sealer was Tile Doctor Colour Grow, an impregnating sealer which is designed to both provide durable surface protection, whilst also intensifying the natural colours within the stone. I applied a layer of Colour Grow carefully to the countertop, and the Onyx shades within the Marble really came to life once again.

Marble Onyx Countertop London Before and After Cleaning

I was very happy with the results overall, as was my client. It is very rewarding to think that hard work can go a long way to quickly restoring a surface which had been hidden for so long by many layers of muck.
 
 

Marble Countertop Restored in Hampstead

Cleaning, Burnishing and Sealing a Limestone Floor in St. John’s Wood

I was recently engaged to refresh the Limestone tiled floor at a house in St. John’s Wood, which is a very affluent area and apparently has the 5th most expensive postcode in London so as you can imagine this was a very expensive floor. The client had requested an improvement condition of the Limestone tiles in the living room and a thorough clean, polishing and seal was required. Over time, the floor in this busy living room – which was also used as a play area for young children – had become dirty and certainly worse for wear with all the use it had been getting. So, I set about my work to get this floor back to looking its best.

Cleaning and burnishing a Limestone floor

My initial task before beginning the cleaning process was to remove any furniture (as well as toys) from the room so I would have a clear area to work in. I then applied a layer of Tile Doctor Pro-Clean cleaner, diluted with water, to the floor. Pro-Clean is also suitable for use on other natural stone floors such as Slate, Granite and Travertine.

After leaving the solution to dwell for a period of a few minutes, I began to scrub the floor with a stiff hand brush. Whilst helping to remove a lot of the built up dirt on the surface of the tiles, the product also stripped off the old sealer and polish. Following this, I paid special attention to the dirty grout lines, cleaning them with Tile Doctor Oxy-Pro, a powerful, high-alkaline cleaner.

Limestone Floor London NW8 After Cleaning Grout Lines with Oxy Pro Limestone Floor London NW8 After Cleaning Grout Lines with Oxy Pro

After completing the cleaning, I rinsed the floor with clean water to remove any excess cleaning products. I then began to burnish the floor using Tile Doctor Diamond encrusted burnishing pads. This was done in four steps, as I used four different pads (coarse, medium, fine and very fine) rinsing the floor with water between each pad. I would recommend using this setup of four pads for restoring the appearance of polished stone floors; you starting with a coarse pad and the gradually work your way up to the very fine pad achieving a high polish finish in the process. I finished of the process with a quick rinse and a buffing pad to give the floor a final polish before I commenced the sealing.

Sealing a Limestone floor

My choice of sealer was Tile Doctor Colour Grow, which is specifically designed to not only provide durable surface protection, but also to intensify the colour of the tiles. The sealer penetrates deep into the pores of the stone, providing water resistance and long-term protection from ingrained dirt and stains. As you can see from the photos, the sealer really helped to accentuate the fantastic natural colours in the Limestone.

Limestone Floor London NW8 After Burnishing Limestone Floor London NW8 After Burnishing

My client was very pleased with the final result, and was amazed by how quickly I had been able to improve the state of her floor which, with a colourful and shiny finish, has really brightened up the living room.
 
 

Full Restoration on Limestone Floor in St. John’s Wood

Victorian Hallway Tile Restoration in London W2

This large entrance hall tiled in Victorian black and white floor tiles in London W2 had been quite badly damaged in the past by having a carpet glued and nailed on to it. Many tiles were broken or missing and those missing had been replaced by cement.

Victorian-Tile-Before-Cleaning-in-London.jpg

Cleaning a Victorian Floor

On the first day of this three day job I removed the cement filling and extracted the nails that remained in the floor. I then stabilised the exposed area with a PVA solution before replacing the missing tiles with replica or salvaged ones to match the floor was swept out and vacuumed to remove all loose debris.

On the second day I cleaned the floor, removing the old carpet glue with Tile Doctor “Remove and Go” which was left to dwell onto the tile for a while to allow it to soak into the tile and break down the adhesive; this was then removed with a wet vacuum. The next step was to clean the tiles using Tile Doctor Pro-Clean which was worked in with a black srubbing pad to scrub the cleaning solution into the tile and finish off the cleaning process, again the soiled solution was removed with a wet vacuum. Normally by now the floor would of have been clean however In this case the levels of soaked-in old glue and ground-in dirt from decades of use were such that the floor also required steaming, scraping and wire brushing with a Spid brass wire brush before a final clean with another round of Pro-Clean and a black buffing pad fitted to a Numatic buffing machine. This had the desired affect and the last step was to wash the floor down with clean water to remove any remaining chemicals etc.

Sealing a Victorian Floor Sealing

After leaving the floor to dry overnight I came back the third day to seal the floor using four coats of Tile Doctor Seal and Go which is ideal for Victorian tiled floors as it leaves a low sheen finish whilst providing excellent stain protection.

Victorian-Tile-After-Cleaning-in-London
As you can see from the ‘before’ and ‘after’ photos the results were impressive and the customer described it as, “looking great”.

Victorian Tiled floor cleaned and sealed in West London

Cleaning a Tumbled Marble mosaic wet room floor in London SE1

This Tumbled Marble mosaic wet room floor was installed in a house in London, SE1 four years before prior and was now looking a little tired. This was mostly caused by a build-up of Limescale which had then become grimy.

Tumbled-Marble-London-Before

Stripping a Tumbled Marble Floor

To treat the Limescale I used Tile Doctor Grout Clean Up which managed to remove most of the scale and to remove the remainder I steamed the tiles using an Earlex Steamer and carefully scraped any remaining Limescale residue away with a Stanley window scraper. To restore the marble itself I used Tile Doctor burnishing pads to re-polish the tiles using 17″ pads on the main area and 8″ pads on a hand-held Clarke polishing machine in the corners. These diamond encrusted pads come in a number of different colours and are applied one after another with each pad being a finer grade than the last. After thoroughly rinsing the stone again and removing the waste water with a wet vacuum. As the marble was naturally fast drying I used an Earlex heat gun to speed dry the floor and repeated this after lunch to ensure the floor was entirely dry before sealing.

Sealing Tumbled-Marble Tiles

Once the Marble tiles were dry I started to seal them using two coats of Tile Doctor Colour Grow sealer which is a great choice for natural stone as it enhances the natural colours in the tile as well as providing stain protection.

Tumbled-Marble-London-After
As the photographs show the results were very good and the customer was highly delighted.

Tumbled-Marble-London-After
 

Restoring Tumbled Marble Mosaic in a Wet Room

Cleaning a Limestone Balcony in St John’s Wood

This balcony in St John’s Wood, London, NW8, which had been clad in Limestone floor tiles, had not been professionally cleaned for 15 years and was now covered in mould which the customer was unable to remove.

Limestone-Balcony-NW8-Before-Cleaning

Stripping the Limestone Tiled Floor

To get the Limestone clean I used a neat solution of Tile Doctor Pro-Clean with was left to soak into the stone before being worked in with rotary machine fitted with a black buffing pad. This process removed most of the mould but there were still some stubborn patches so I then used a further application of Pro-Clean this time mixed 50/50 with Nanotech Ultra Clean to add an abrasive element to what is a powerful alkaline cleaning product. This was scrubbed into the tile and then steamed off using a Bosch steamer followed by further scrubbing by hand.

The next step was to use a set of four Tile Doctor burnishing pads to polish the Limestone surface to a low sheen. These diamond encrusted pads come in a number of different colours and are applied one after another with each pad being a finer grade than the last. After thoroughly rinsing the stone again and removing the waste water with a Numatic aqua vacuum I left the tiles to dry off overnight. Luckily the weather remained fine.

Sealing Yorkshire Limestone Tile

The next day I sealed the Limestone tiles using two coats of Tile Doctor Colour Grow sealer which I prefer for Limestone as it enhances the natural colours in the Limestone floor as well as providing stain protection something I’m sure it’s going to need given the location.

Limestone-Balcony-NW8-After-Cleaning
Although not quite all the damage from the mould could be entirely removed the tile was 95% improved and the customer was very satisfied with what had been achieved.

Limestone Restoration in St John’s Wood

Limestone tiles hallway cleaned and polished in Notting Hill

This was a Limestone tiled hallway at a house in Notting Hill, London W2 where extensive renovations had just been completed. The floor had been badly affected by being left uncovered during the building works as well as having a build-up of many years of dirt and stains on its surface. The tiles had been laid more than twenty years ago and had not been cleaned or sealed since.

The customer was considering replacing the floor as she believed that it was beyond restoring. As well as ingrained dirt there were several quite severe rust stains and large ring-shaped marks that looked as if they had come off the bottom of paint or varnish tins.

Limestone Tile Cleaning During

Cleaning the Limestone Tiled Floor

I used a black buffing pad on my Numatic buffing machine and neat Tile Doctor “Pro-Clean” to perform an initial deep clean on the floor. In order to re-polish the floor and not leave it too porous I then used the a red and then a white diamond encrusted burnishing pad. Even after this some stains remained, so at this point I used Tile Doctor “Reduxa” stone stain remover to attack the stubborn ingrained marks. All of these were successfully removed except for two very deep rust stains which, never-the-less, were reduced in size and intensity by about 70%.

After this I used a yellow burnishing pad to return the floor to its original finish.
At this point, as one of the tiles was broken at the edge and a piece missing, I used Akemi stone floor repair filler to fill in the broken piece with a filler that is stronger than the original stone.

Limestone Tiles After Cleaning

Sealing the Limestone Floor

The next day I returned to seal using Tile Doctor “Colour Grow” Sealer.
Unfortunately, I forgot to take a “before” picture until after I had started this job but still the transformation is clear from the photos that I took. When the limestone was fully restored it was found to have attractive bedding lines running through it and to be all-in-all a very nice looking floor.

Limestone Tiles After Cleaning

The customer was amazed by what had been achieved and very pleased that she had opted for restoration over the far more expensive option of replacement.
 
 

Limestone Floor Cleaned and Sealed in London

Terracotta Floor Tile Restoration in Clapham SW9

We had our work cut out for us restoring this Terracotta floor installed in the kitchen of a house in Clapham, south west London. Over the years it had been covered with many layers of metallised emulsion polish, this had been put on without a primer and Terracotta being porous it had soaked into the tile. Various efforts to remove it in the past had not been successful and had resulted in some damage to the floor. This had been covered by yet more layers of metallised emulsion which had yellowed and oxidised over time.

Terracotta Floor Before

Cleaning Terracotta Tiles

Working in stages, I laid down Tile Doctor Remove and Go, which is a powerful coating remover, to break down the layers of metallised emulsion and then steamed the tiles and scraped and wire-brushed the remnants of it away. Once this was done more Remove and Go was applied to the terracotta tile to remove the polish that had sunk deep into the tile when it was first applied more than twenty years before. Again a steamer was required to help bring out what was left of the original misused sealer! Once I was happy this was followed by a thorough clean with a dilution of Tile Doctor Pro-Clean scrubbed in with a black buffing pad fitted to a Numatic floor buffing machine. Last step was to give the floor a thorough rinse with water in order to remove any remaining chemical and neutralise the Terracotta.

Terracotta Floor During

Sealing Terracotta Floor Tiles

After two days work cleaning the floor I left it to dry out overnight and returned to seal on the third day using six coats of Tile Doctor Seal and Go which will protect the floor and also gives the surface an attractive low sheen. You can see the transformation in the floor and the customers were very impressed and preferred the lightened natural look compared to its previous appearance.

Terracotta Floor After
 

Terracotta Tiles Transformed in South London.

Emery and Cie Cement Encaustic tiles Restored in Ealing

This unusual Emery and Cie Cement Encaustic tiled floor in Ealing W5 had been poorly installed by the tiler with grout haze on the tiles and the wrong sealer used. Cement encaustic tiles are quite delicate and difficult to restore.

Cleaning Cement Encaustic Tiles

I used a red burnishing pad fitted to a buffing machine to cut into the tile surface and remove the grout haze and old sealer. The next step was to apply a dilution of Tile Doctor Pro-Clean letting it soak into the tile before working it in to the tile with a red buffing pad. The soiled cleaning solution was then removed using a wet and dry Vacuum and the floor washed down with clean water. This cleaned up the floor well but there were some stubborn stains which were removed using a steamer.

Cement Encaustics Before Emery and Cie Tiles After

Sealing Cement Encaustic Tiles

Once the floor had dried it was sealed using three coats of Tile Doctor Colour Grow which is a colour intensifying sealer that provides durable surface protection. Last step was to burnish the tiles again with a green burnishing pad to bring up the shine.

Although the floor had been too damaged to be made perfect, it was very much better when I had finished and the customer was delighted with the result.

Cement Encaustic tiles cleaned and Sealed in London

Slate Tiled Wet Room floor in Ealing

This was a slate floor in a wet room in a house in Ealing W5. The black semi-riven slate had originally been sealed by the tiler on installation but had never looked how the customer wanted it to.

Cleaning Semi-Riven Slate Tiles

To strip off what was left of the old sealer we used Tile Doctor Remove and Go leaving it to soak into the floor for a while before working it in with a rotary machine fitted with a black buffing pad. The solution was then removed using a wet and dry Vacuum and the floor washed down with clean water. This work removed any remaining sealer but we still needed to give the floor a deep clean and so the whole process was repeated this time using Tile Doctor Pro-Clean which is an effective heavy duty alkaline cleaning product ideal for cleaning up natural stone floors and grout. After we gave the floor a thorough rinse to remove any cleaning products and neutralise the floor ready for sealing, last step was to remove the water from the floor using the wet vacuum again and leave it to dry out overnight.

Semi Riven Slate Floor Before

Sealing Semi-Riven Slate Tiles

The next way came back and sealed the floor using two coats of Tile Doctor Colour Grow as you can see from the photographs did an excellent job lifting the colour out of the tile.

Semi Riven Slate Floor After
The customer was very pleased to have a well-sealed black slate with a slight sheen instead of the dull-looking grey floor she had had before.

Semi Riven Slate Tiled Bathroom floor Cleaned and Sealed in London

Cleaning an Edwardian Quarry Tiled Porch

These photographs are from an Edwardian Quarry tiled porch at a house in central London. The tiles had previously been sealed with several layers of varnish which was now beginning to wear off in places and was making the entrance to the house look very untidy.

Cleaning Edwardian Quarry Tiles

I used a mixture of Tile Doctor Remove and Go and Nanotech Ultra Clean and left it to soak into the floor for an hour to break down the old varnish. The floor was then rinsed with clean water and steamed to remove any remaining residue. Following this I used a solution of Tile Doctor Pro-Clean cleaner worked into the floor with a rotary machine fitted with a black buffing pad to machine clean the floor giving it another rinse to neutralise the floor of any chemicals before leaving for the day

Edwardian Quarry Tiled Porch Before Cleaning

Sealing Quarry Floor Tiles

The next day the tiles had dried out overnight and were ready for sealing for which we used three coats of Tile Doctor Colour Grow which is a durable sealer that helps to lift the colour out of the tile.

Edwardian Quarry Tiled Porch After Cleaning and Sealing
You can see the difference in the floor from the photographs in fact the customer said that they had put up with the condition of the tiles in the porch for ten years and were very pleased to have found a solution with Tile Doctor.

Edwardian Quarry Tiled floor restoration in London

Varnished Quarry Tiled Hallway Restored in London SW11

This Quarry tiled hallway installed in a house in South West London had been varnished many years previously and was worn through leaving a dark and uneven appearance and difficult to clean.

Cleaning the Quarry Tiled Floor

We started cleaning the Quarry Tiles by applying a strong solution of Tile Doctor Pro-Clean worked into the floor using a buffing machine fitted with a black scrubbing pad. Although this had an effect on the Varnish it was proving difficult to shift so using a scraper tool it was manually scraped off the floor. The floor was washed down with clean water and then cleaned again using Pro-Clean before finally washing down three more times using clean water in order to neutralise the floor and remove any trace of cleaning products before sealing.

Quarry-Tiled Hallway before cleaning

Sealing Quarry Floor Tiles

The floor was left to dry overnight and I came back the next day to apply the sealer. For sealing the Quarry tiles I used five coats of Tile Doctor Seal and Go, it’s recommended for Quarry tiles and adds a nice low sheen to the floor; sealing does take time as it’s necessary to allow each coat to dry before applying the next so it took most of the day to complete the job. You can see the difference in the floor which has come up a lot lighter and is now much easier to maintain.

Quarry-Tiled Hallway after cleaning and sealing
 

Removing Varnish from a Quarry Tiled Floor in London SW11

Polishing a Granite & Limestone floor tile in Westminster

This interesting unusual Granite and Limestone tile combination was installed in the kitchen of a house in Westminster, London. The black Granite was looking Dull and the Limestone had a dirty appearance of the tile surface which had lost its shine and was looking dull.

Stripping the Granite and Limestone Tiled Floor

To resolve we had to strip back the Granite and Limestone surfaces using a set of burnishing pads, these diamond encrusted pads come in a number of different colours each one has a different grade of coarseness and does a different job from scrubbing to polishing. I started with the red pad together with water and then carried on with the white, then yellow pads using water. Finally when I had dried the floor I used a green pad to buff the floor up. This activity took most of the day so left the floor to dry overnight.

Granite and Limestone Kitchen floor before

Sealing Granite and Limestone Tiles

The next morning I arrived to find the floor had dried out sufficiently for it to be sealed which was done using a couple of coats of Tile Doctor Colour Grow. Colour Grow is a a great sealer for lifting the natural colours out in hard stone flooring such as Granite and Limestone floor as well as providing stain protection. Once the sealer had dried I then finished it all off with a quick buff using a white buffing pad.

Granite and Limestone Kitchen floor after
You can see from the photographs how the combination of the burnishing pads and sealer and really lifted the look of the floor.

Terracotta Tiled Floor Cleaned and Sealed in Tooting

We were asked to take a look at this Terracotta Tiled floor in Tooting, South London which were becoming difficult to clean and in need of a good clean and seal.

Cleaning Terracotta Tile

We started the task by applying a strong solution of Tile Doctor Pro-Clean, which is a heavy duty alkaline product designed for cleaning tiles; this was scrubbed in with a black pad fitted to a rotary machine. I had to repeat this process a couple of times and also use a stiff brush along the grout lines which cleaning pads often struggle to reach. Once we were happy the floor was clean it was thoroughly rinsed the floor with clean water to remove any remaining chemical and it was left to dry overnight.

Terracotta Tile Before Cleaning in Tooting

Sealing Terracotta Tile

The following day we checked the floor was clean and dry and took care of any ugly spots that we have overlooked the day before and then proceed to seal. For Terracotta I recommend Tile Doctor Seal and Go, it’s a water based sealer so it doesn’t give off an odour when it’s drying and also offers durable stain protection together with a low sheen finish. Terracotta is a very porous material and in the end the floor actually needed seven coats of sealer applied with a paint pad before it was fully sealed, which naturally takes a long time to apply as you have to wait for it to dry before applying the next coat.

Terracotta Tile After Cleaning in Tooting
The customer delighted with results.

Terracotta Floor Cleaned and Sealed in London

Polishing hard Magnesium Limestone floor tiles in London SW18

The owner of this house in Wandsworth had imported these hard magnesium Limestone tiles direct from Italy and fitted them into a conservatory three years prior; over they years however they had lost their shine and started to go dull and look uninviting. This is fairly normal for polished stone which does need to be re-polished for it to keep its appearance however the owner was unhappy with the finish and wanted it re-polished. There were also a number of naturally formed holes in the Limestone floor and these needed filling to give a completely even appearance.

Stripping and Polishing the Limestone Tiled Floor

To resolve we filled the holes using grout coloured to match the Limestone surface and then proceeded to strip back the tile surface using a set of burnishing pads. These diamond encrusted pads come in a number of different colours each one does a different job from scrubbing to polishing. I started with the red pad together with water and then carried on with the white, then yellow pads using water. Finally when I had dried the floor I used a green pad to buff the floor up. This activity took most of the day so left the floor to dry overnight.

 

Sealing Magnesium Limestone Tile

The next morning I arrived to find the floor had dried out and so began to seal it which was done using a couple of coats of Tile Doctor Colour Grow which does what it says on the bottle and as well as provided stain protection lifted the natural gold colour in the Limestone floor. Once the sealer had dried I then finished it all off with a quick buff using a white buffing pad.

Imported hard magnesium limestone after
Apologies for not capturing a good before photograph for comparison, I can tell you however that the owner was very pleased with the results and reported they looked better than when they were new.

Hard magnesium limestone tiled floor polished in Wandsworth SW18

Removing Grout Haze in a Shower Cubicle, London NW1

These ceramic mosaic tiles were fitted in square sheets in a shower cubicle at house in London NW1. You can clearly see from the first photograph that the tiler did not remove the grout from the tile before it set leaving grout haze on most of the tile and a nice white band of grout between the mosaic sheets.

Removing Grout Haze

To clean up the ceramic tiles and remove the grout we sprayed on Tile Doctor Grout Clean-up which is a specialist acid based product that penetrates below the surface of the grout to remove allowing it to be removed. It’s reasonably easy to apply, you need to wet the tile first and then apply a dilution of the Grout Clean-up, leave it dwell on the tile for a few minutes allowing it to get to work and then scrub it in. With it being an acid it’s important not to leave it on the tile very long and wash it off within five minutes and rinse down the tile with water.

Ceramic Shower Cubicle Grout Haze Before Ceramic Shower Cubicle Grout Haze After

Cleaning Ceramic Mosaic Tiles

Once the tiles were free of grout the next step was to clean the tiles for which we used Tile Doctor Pro-Clean which is a versatile alkaline tile cleaning product that can be diluted in different strengths depending on if your looking to clean the tile or strip sealers. In this case we could also of used Tile Doctor Oxy-Pro shower Tile and Grout Cleaner which is a ready to use tile and grout cleaner that comes with a spray nozzle attachment, the spray allows the cleaning agent to mix with air making it lighter and easier to stick to vertical surfaces. This is important as you need to let the cleaning agent dwell on the surface of the tile and grout for a few minutes before scrubbing it by hand with a stiff brush and then washing it off with clean water.

The ceramic mosaics did not need sealing so the renovation was now complete, grout removed and tiles cleaned, and naturally the customer was very pleased with the results and the cubicle was transformed.

Shower Cubicle Restored in London NW1